Voltage Detectors

Measures from 0.5Arms to 300Arms Accuracy 1% of Reading ± 0.3A TRMS measurements when connected to a TRMS instrument No core saturation or damage if overloaded 9V battery for typical 140 hour continuous operation 1MHz frequency response Low phase shift for power measurements Insensitive to DC, measures only AC component on DC AC signals Excellent linearity Lightweight Sensor is resistant to oils and aliphatic hydrocarbons EN 61010, 1000V CAT III, 600V CAT IV, CE Mark

Measures from 0.5Arms to 300Arms Accuracy 1% of Reading ± 0.2A TRMS measurements when connected to a TRMS instrument No core saturation or damage if overloaded Overrange LED for measurement circuitry EN 61010, 1000V CAT III, 600V CAT IV, CE Mark 20kHz frequency response Low phase shift for power measurements Insensitive to DC, measures only AC component on DC AC signals Excellent linearity

Measures from 0.5Arms to 300Arms Accuracy 1% of Reading ± 0.3A TRMS measurements when connected to a TRMS instrument No core saturation or damage if overloaded 9V battery for typical 140 hour continuous operation 1MHz frequency response Low phase shift for power measurements Insensitive to DC, measures only AC component on DC AC signals Excellent linearity Lightweight Sensor is resistant to oils and aliphatic hydrocarbons EN 61010, 1000V CAT III, 600V CAT IV, CE Mark

Measures from 0.5Arms to 3000Arms Accuracy 1% of Reading ± 0.2A TRMS measurements when connected to a TRMS instrument No core saturation or damage if overloaded Overrange LED for measurement circuitry EN 61010, 1000V CAT III, 600V CAT IV, CE Mark 20kHz frequency response Low phase shift for power measurements Insensitive to DC, measures only AC component on DC AC signals Excellent linearity

Three testers in one Identify circuit breaker to an electrical socket Trace AC cables in walls Sort wires in a bundle Microprocessor controlled Coded transmission allows easy separation of transmitter signal Audible and visual indicators Low battery indicator Cable tracing depth – up to 40 cm NEMA 5-15 plug > Each Unit Includes Padded carrying case 9V battery User’s manual

Meter detects faulty wiring in need of repair without removing outlets cover plates, or panel covers: Faulty splices and connections, Incorrect wiring, Undersized wiring, Faulty GFCIs, Faulty or incorrectly wired AFCIs, Incorrect line voltage, Poor ground quality Testing efficiency relevant test data (voltage, voltage drop, hot and neutral voltage drop, voltage with load, ground impedance) is presented on a single large display to save operator time no scrolling or switching screens needed Verifies if wiring is tested for load carrying ability that it meets electrical code recommendations for voltage drop under load User selectable 0, 10,15 and 20 amps loads to verify performance of the electrical system Incorrect wiring or voltage drop test failure is clearly indicated by flashing screen Will not trip circuit breakers or blow fuses during the test Tests GFCI and AFCI operations Check ground quality for safety and ability to support sensitive electronic equipment Measure fault currents Save money and time by eliminating guess work NOTE: The Inspector™ III does not check the condition of wiring insulation Load: Constant 0, 10, 15 or 20 AMP simulation regardless of line voltage Operating Voltage: 95-140 VAC /-2%, /- 2 digits GFI Trip: 6.0 mA nominal to trip GFI, 30 mA to trip RCD AFCI Trip: Up to 8, 120 AMP pulses within 1/2 second period > Each Unit Includes Power Cord 9V Alkaline Battery (Installed) Users Manual Carrying Case

Customers can safely detect high voltage with the TIC 300 PRO – now with VolTect™. It intuitively alerts them when used in close proximity to an energized line. Utility tool for checking transmission lines, power distribution equipment, down power lines, fuses, and load break connectors Lower voltage setting for checking voltage presence in breaker panels, breakers, power outlets and wiring Verifies presence of Voltage from 30 VAC to 122,000 VAC (122kV) Non-contact AC voltage detection Visual and audible voltage indication Self-test verifies that tester works properly Ergonomic design with a convenient handle Drop-proof to 6-FT Used with Hot Stick Tic 410A for voltage higher than 1500 VAC > Each Unit Includes Deluxe carrying case 9 V battery (installed) Instruction Manual

HT-10KVPAC Hipot / Dielectric Tester with microcontroller technology for ease of use. AC output 0-10,000Vac @ 10mA. Ships complete with cables, manual, and Calibration Certificate. Made in the USA. Features HT10000P AC: AC output to 10000 Volts. Delivers 1 through 8 milliamps. Custom outputs to 25 mA. Logic Controlled, One-button testing. LED indicators. Buzzer upon failure, test terminates. Test termination defeatable by switch on rear panel. Provided with arc detection circuit to properly detect hipot failures. Rear panel adjustments, leakage limit, ramp time, test time and voltage. Ergonomic design for safety and ease of use. High voltage output jack. Automatic voltage ramp-down circuit eliminates residual voltage. Designed for product development and laboratory use. High efficiency design, low power consumption. All test leads included. Calibrated to NIST standards. 1 year warranty HTT-1 and HTT-1RHipot and Ground Continuity Function Checker Compatible