Power Analyzers

Frequency range of 9 kHz to 110 GHz (sensor dependent) Wide dynamic range of -70 to 44 dBm (sensor dependent) Speed improvement by 2X for E-Series sensors: up to 400 readings/sec Go beyond GPIB with LAN LXI-C and USB connectivity Code-compatible with E4418B, E4419B, power meters Code-compatible with 436A, 437B, and 438A power meters (option 200) Increased measurement channels: up to three channels with two additional U2000 Series power sensors connected using the optional USB hosts Automated frequency/power sweep measurements with the optional external trigger in/out feature

Frequency range of 9 kHz to 110 GHz (sensor dependent) Wide dynamic range of -70 to 44 dBm (sensor dependent) Speed improvement by 2X for E-Series sensors: up to 400 readings/sec Go beyond GPIB with LAN LXI-C and USB connectivity Code-compatible with E4418B, E4419B power meters* Code-compatible with 436A, 437B and 438A power meters (option 200) Increased measurement channels: up to three channels with two additional U2000 Series power sensors connected using the optional USB hosts Automated frequency/power sweep measurements with the optional external trigger in/out feature

EEPROM to store cal factors eliminates manual entry Wide frequency range from 10 MHz to 18 GHzc Wide dynamic range from -35 dBm to 20 dBm Best-in-class power linearity of less than 1%, excellent SWR of mismatch uncertainty and highly accurate power repeatability Accurate calibration and traceability to US National Institute of Standards and Technology (NIST) SCPI codes compatible with 8480 series (option CFT) > > Note: Option CFT is available as a replacement of legacy 8480 Series power sensors intended for cal factor manual entry and SCPI compatibility. Option CFT is not compatible with 43x and other obsolete power meters. SCPI codes compatible with E-Series sensor (standard option) Compatible with EPM (new N1913/14A, E4418/19B), EPM-P (E4416/17A), P-Series (N1911/12A) power meters (Firmware upgrade required) > > Note: All N8480 series power sensors are not compatible with the Keysight 43x, E1416A, N8262A power meters, 5314x microwave counters, and E7495x base station test set. N8480 Series Power Sensors are the replacement solutions for 8480 Series Power Sensors. The new power sensors are integrated with EEPROM feature, which allows users to calibrate the power sensors without manually entering the calibration factors to the power meter. By comparing to legacy 8480 Series Power Sensors, there are tremendous improvements such as wider dynamic range and frequency range, better accuracy, linearity, repeatability, and SWR.

EEPROM to store cal factors eliminates manual entry Wide frequency range from 50 MHz to 50 GHz Wide dynamic range from -35 dBm to 20 dBm Best-in-class power linearity of less than 1%, excellent SWR of mismatch uncertainty and highly accurate power repeatability Accurate calibration and traceability to US National Institute of Standards and Technology (NIST) SCPI codes compatible with 8480 series (option CFT) Note: Option CFT is available as a replacement of legacy 8480 Series power sensors intended for cal factor manual entry and SCPI compatibility. Option CFT is not compatible with 43x and other obsolete power meters. SCPI codes compatible with E-Series sensor (standard option) Compatible with EPM (new N1913/14A, E4418/19B), EPM-P (E4416/17A), P-Series (N1911/12A) power meters (Firmware upgrade required) Note: All N8480 series power sensors are not compatible with the Keysight 43x, E1416A, N8262A power meters, 5314x microwave counters and E7495x base station test set. > N8480 Series Power Sensors are the replacement solutions for 8480 Series Power Sensors. The new power sensors are integrated with EEPROM feature, which allows users to calibrate the power sensors without manually entering the calibration factors to the power meter. By comparing to legacy 8480 Series Power Sensors, there are tremendous improvements such as wider dynamic range and frequency range, better accuracy, linearity, repeatability, and SWR.

Keysight U2000 Series USB power sensors make setup and measurement fast without the need of a power meter, just plug the USB sensor cable to the PC, you can control the USB power sensor with the FREE Power Panel (N1918A) software. The U2000 Series is also supported by the Keysight BenchVue software. BenchVue makes it easy to control your power meter to log data and visualize measurements in a wide array of display options without any programming. Frequency range of 10 MHz to 18 GHz Wide dynamic range of -60 to 20 dBm Internal zeroing capability to eliminate external calibration High measurement speed of up to 250readings/second Support internal and external trigger measurements Display power measurements on a PC or other Keysight’s instruments Internal triggering and trace display capability Includes BV0007B Power Meter app

Frequency range of 10 MHz to 50 GHz Fastest measurement speed for thermocouple sensor, &gt, 900 readings/s (free run/fast buffer mode) Best-in-class power linearity of less than 0.8% Wide dynamic range from -35 dBm to 20 dBm Real time measurement uncertainty (MU) feature S-parameter and gamma correction function Accurate calibration and traceability to US National Institute of Standards and Technology (NIST) or National Physical Laboratory (NPL) BenchVue software enabled Includes BV0007B Power Meter app

Broad 10MHz to 6GHz frequency range enables use in a wide variety of applications Wide dynamic range of -63dBm to 20dBm Integrated power sensor eliminates the need to carry a separate power sensor Internal power reference enable self calibration Absolute accuracy as good as ±0.21dB Powered from batteries, AC-DC converter module or a computer via USB interface > The V3500A Handheld RF Power Meter is a compact, handheld instrument that makes accurate RF power measurements in both field and manufacturing applications. With an absolute accuracy as good as ±0.21dB, a wide frequency range of 10MHz to 6GHz, and a measurement range of -63dBm to 20dBm, the V3500A is suitable for a wide variety of RF measurement applications. Its built-in power sensor eliminates the need for users to carry both an instrument and a separate sensor module. Truly portable, the V3500A fits easily into your hand or a toolkit. An optional belt loop holster or carrying case with shoulder strap is also available. To optimize flexibility, it is capable of drawing operating power from batteries, an AC-DC converter module, or a computer via USB interface.

POWER QUALITY SIMULATOR Creates 3 Phase 50/60Hz Voltage and Current. Powered from 12VDC adapter. Create dips, swells, transients, THD events, harmonics and more. Comes complete with CT cables, universal power adapter and operational manual Ideal for power quality training Easily create sags, swells, transients and harmonic events Simulate voltage flicker, leading and lagging power Create phase shift events Simulate three phases of voltage and current at 115 V ac or 230 Vac Operates off single-phase voltage > Ideal for power quality training Easily create sags, swells, transients and harmonic events Simulate voltage flicker, leading and lagging power Create phase shift events Simulate three phases of voltage and current at 115 V ac or 230 Vac Operates off single-phase voltage > The MPQSIM Megger Power Quality Simulator is used for demonstrations and as a training tool. It is the perfect tool to use with the MPQ and PA9 Series. The MPQSIM provides a simple and easy method for simulating a three-phase voltage configuration off of a standard single-phase source. The simulator provides both continuous voltages/currents and harmonics for trending as well as instantaneous events for power quality demonstrations and training. Applications The MPQSIM Power Quality Simulator is ideal for power quality training courses and demonstrations of power quality phenomenon. The MPQSIM will allow you to see signatures of different types of power quality phenomenon. It also allows you to learn how to program a power quality analyzer to capture these phenomenon.