Multifunction Calibrators

The MFT 4010 is a multifunctional calibrator with full HART digital communications capability It can be used to measure pressure, differential pressure, to source or measure temperature, to source or measure voltage or current, to calibrate field devices, and to document the performance of field devices The MFT 4010 consists of a handheld base unit with three bays for sensor modules The MFT 4010 pressure modules are NIST traceable to /- 0.025% of full scale and are fully temperature compensated for the best accuracy across a broad temperature range RTD and T/C modules measure or simulate a wide variety of temperature types with NIST traceable accuracy

Accuracy up to ± 0.006% rdg Calibrate temperature, pressure, current dc, voltage, frequency and resistance Internal/External pressure modules and dual channels HART ability for Smart Transmitters Documenting capabilities using CalpMan software package Dimensions 290 x 98 x 57 mm condensing Weight 2.5Kg Relative humidity Max 95%RH non Storage temp.: from 0°C to 60°C (excluding batteries) Operating environment temp. range: from -10°C to 50°C > Each Unit Includes Rubber holster Battery Charger Instruction manual and calibration report Test leads

Accuracy up to ± 0.006% rdg Calibrate temperature, pressure, current dc, voltage, frequency and resistance Internal/External pressure modules and dual channels HART ability for Smart Transmitters Documenting capabilities using CalpMan software package Dimensions 290 x 98 x 57 mm condensing Weight 2.5Kg Relative humidity Max 95%RH non Storage temp.: from 0°C to 60°C (excluding batteries) Operating environment temp. range: from -10°C to 50°C > Each Unit Includes Rubber holster Battery Charger Instruction manual and calibration report Test leads

Accuracy up to ± 0.006% rdg Calibrate temperature, pressure, current dc, voltage, frequency and resistance Internal/External pressure modules and dual channels HART ability for Smart Transmitters Documenting capabilities using CalpMan software package Dimensions 290 x 98 x 57 mm condensing Weight 2.5Kg Relative humidity Max 95%RH non Storage temp.: from 0°C to 60°C (excluding batteries) Operating environment temp. range: from -10°C to 50°C > Each Unit Includes Rubber holster Battery Charger Instruction manual and calibration report Test leads

Accuracy: ± 0.005% of range 5 ranges from 1CPH to 20.000KHz for source and read Totalize inputs/outputs from 1 to 99999 in 1.0 to 100.0 minutes Read a wide range of frequencies and waveforms from 50mV to 120V peak Source sine and square waves, zero based, or zero crossing Adjustable amplitude from 100mV to 12V peak-to-peak Gate trigger LED flashes in synch with the output frequency. This allows easy adjustment of the attenuation for proper gate triggering EZ-Dial™ knob easily adjust output by 1 Pressing down and turning will select a faster dialing speed EZ-Check™ switch for 0% and 100% span adjustments Store new EZ-Check™ values by pressing the EZ-Dial™ knob Uses a standard 9V Alkaline Battery Superior battery life of 45 hours under typical continuous usage Easy access to battery compartment Lightweight, Rugged and Reliable Small, tough and protected to 60V

Lighten up your toolbox Pocket sized calibrator replaces toolbox of single function devices Milliamp • Voltage • Frequency • Thermocouples • RTDs • Check Continuity Technician friendly operation Intuitive EZ-DIAL Double Click Menu makes it easier to setup than other multifunction calibrators. Uses the same menus as the single function PIE Evolution Calibrators. Icons on the display indicate where to plug in the test leads. Use it as a milliamp and voltage calibrator Source 0 to 24.00 mA, 0 to 10.25 V and -10.00 to 80.00 mV dc Read to 24.00 mA, 10.25 V, 60.0 V and -10.00 to 80.00 mV dc Simulate 2-Wire Transmitters Power up transmitters & loops with the built-in 24 V power supply Simplify HART hookups with built-in 250 Ohm resistor > Calibrate directly in temperature (°C & °F) The PIECAL 820 works with the instruments you use Types J, K, T, E, R, S, B, N, G, C, D, L (J DIN), U (T DIN) and P (Platinel II) Pt 100 Ohm (3850, 3902, 3916, 3926) & 1000 Ohm (3850) Copper 10 & 50 Ohm, Nickel 110 and 120 Ohm > Checkout flow and vibration systems Source & read frequency to 2000 CPM (Counts-Per-Minute), 999.99 Hz, 9999.9 Hz & to 20.000 kHz. Troubleshoot loop & wiring problems ‘Beep’ out connections with the built-in continuity checker Easy to read Turn on the backlight & easily see the display in dark areas of the plant. Quickly set any three outputs plus automatic stepping & ramping Easily set any value quickly with the adjustable “DIAL” plus store any three output settings for instant recall with the EZ-CHECK™ switch. Choose between 2, 3, 5 & 11 steps to automatically increment the output in 100%, 50%, 25% or 10% of span. Select RAMP to smoothly increase and decrease the output between Zero and Span. Set step/ramp time to match your system from 5, 6, 7, 8, 9, 10, 15, 20, 25, 30 and 60 seconds. Measure temperature sensors, frequency pickups, loop currents and voltage levels Check the values of your process sensors. Instantly recall MAX and MIN values to see process variability Evolutionary design PIECAL Calibrators are designed and built by members of the same team that designed and built the calibrators manufactured by Fluke* under the Altek* label. The PIECAL 820 improves upon other brands by including a rubber boot, a backlit display with larger digits, higher accuracy and more ranges for greater flexibility.

Save over $393 with the PIE 820 F VIP Kit. Limited Time Offer. FREE Fenix TK75 LED Searchlight, 4,000 Lumens with Batteries and Charger FREE 128 Pack of Green Calibration Labels Lighten up your toolbox Pocket sized calibrator replaces toolbox of single function devices Milliamp • Voltage • Frequency • Thermocouples • RTDs • Check Continuity Technician friendly operation Intuitive EZ-DIAL Double Click Menu makes it easier to setup than other multifunction calibrators. Uses the same menus as the single function PIE Evolution Calibrators. Icons on the display indicate where to plug in the test leads. Use it as a milliamp and voltage calibrator Source 0 to 24.00 mA, 0 to 10.25 V and -10.00 to 80.00 mV dc Read to 24.00 mA, 10.25 V, 60.0 V and -10.00 to 80.00 mV dc Simulate 2-Wire Transmitters Power up transmitters & loops with the built-in 24 V power supply Simplify HART hookups with built-in 250 Ohm resistor > Calibrate directly in temperature (°C & °F) The PIECAL 820 works with the instruments you use Types J, K, T, E, R, S, B, N, G, C, D, L (J DIN), U (T DIN) and P (Platinel II) Pt 100 Ohm (3850, 3902, 3916, 3926) & 1000 Ohm (3850) Copper 10 & 50 Ohm, Nickel 110 and 120 Ohm > Checkout flow and vibration systems Source & read frequency to 2000 CPM (Counts-Per-Minute), 999.99 Hz, 9999.9 Hz & to 20.000 kHz. Troubleshoot loop & wiring problems ‘Beep’ out connections with the built-in continuity checker Easy to read Turn on the backlight & easily see the display in dark areas of the plant. Quickly set any three outputs plus automatic stepping & ramping Easily set any value quickly with the adjustable “DIAL” plus store any three output settings for instant recall with the EZ-CHECK™ switch. Choose between 2, 3, 5 & 11 steps to automatically increment the output in 100%, 50%, 25% or 10% of span. Select RAMP to smoothly increase and decrease the output between Zero and Span. Set step/ramp time to match your system from 5, 6, 7, 8, 9, 10, 15, 20, 25, 30 and 60 seconds. Measure temperature sensors, frequency pickups, loop currents and voltage levels Check the values of your process sensors. Instantly recall MAX and MIN values to see process variability Evolutionary design PIECAL Calibrators are designed and built by members of the same team that designed and built the calibrators manufactured by Fluke* under the Altek* label. The PIECAL 820 improves upon other brands by including a rubber boot, a backlit display with larger digits, higher accuracy and more ranges for greater flexibility.

Product Highlights: Save over $147 with the PIE 820 L VIP Kit. Limited Time Offer. FREELeatherman Sidekick Fuse Tool FREEAmprobe 5XP Digital Multimeter FREE 128 Pack of Green Calibration Labels Lighten up your toolbox Pocket sized calibrator replaces toolbox of single function devices Milliamp • Voltage • Frequency • Thermocouples • RTDs • Check Continuity Technician friendly operation Intuitive EZ-DIAL Double Click Menu makes it easier to setup than other multifunction calibrators. Uses the same menus as the single function PIE Evolution Calibrators. Icons on the display indicate where to plug in the test leads. Use it as a milliamp and voltage calibrator Source 0 to 24.00 mA, 0 to 10.25 V and -10.00 to 80.00 mV dc Read to 24.00 mA, 10.25 V, 60.0 V and -10.00 to 80.00 mV dc Simulate 2-Wire Transmitters Power up transmitters & loops with the built-in 24 V power supply Simplify HART hookups with built-in 250 Ohm resistor > Calibrate directly in temperature (°C & °F) The PIECAL 820 works with the instruments you use Types J, K, T, E, R, S, B, N, G, C, D, L (J DIN), U (T DIN) and P (Platinel II) Pt 100 Ohm (3850, 3902, 3916, 3926) & 1000 Ohm (3850) Copper 10 & 50 Ohm, Nickel 110 and 120 Ohm > Checkout flow and vibration systems Source & read frequency to 2000 CPM (Counts-Per-Minute), 999.99 Hz, 9999.9 Hz & to 20.000 kHz. Troubleshoot loop & wiring problems ‘Beep’ out connections with the built-in continuity checker Easy to read Turn on the backlight & easily see the display in dark areas of the plant. Quickly set any three outputs plus automatic stepping & ramping Easily set any value quickly with the adjustable “DIAL” plus store any three output settings for instant recall with the EZ-CHECK™ switch. Choose between 2, 3, 5 & 11 steps to automatically increment the output in 100%, 50%, 25% or 10% of span. Select RAMP to smoothly increase and decrease the output between Zero and Span. Set step/ramp time to match your system from 5, 6, 7, 8, 9, 10, 15, 20, 25, 30 and 60 seconds. Measure temperature sensors, frequency pickups, loop currents and voltage levels Check the values of your process sensors. Instantly recall MAX and MIN values to see process variability Evolutionary design PIECAL Calibrators are designed and built by members of the same team that designed and built the calibrators manufactured by Fluke* under the Altek* label. The PIECAL 820 improves upon other brands by including a rubber boot, a backlit display with larger digits, higher accuracy and more ranges for greater flexibility.