Motor Testing

Motor Test Kit {Medium Voltage} includes: 6524: Multifunction Insulation Resistance Tester, 1000V True Megohmmeter 1 kV Insulation and Multi-Function Tester (Resistance, Continuity, Frequency and Voltage) 50V, 100V, 250V, 500V and 1000V Insulation Test Voltages 200GΩ Max Insulation Resistance DAR and PI ratios calculated Timed Test Mode up to 40 minutes for Insulation Resistance Test Test Lock feature for hands free timed measurements up to 15 minutes Continuity tests at 20mA or 200mA Test lead resistance compensation for accurate low resistance measurements True RMS AC/DC Voltmeter up to 700V Ohmmeter to 1000kΩ Frequency measurements from 15 to 800Hz Auto discharge after Insulation Test Hold function to freeze readings Large and bright dual display with blue backlight Auto Standby Feature due to inactivity saves battery power 300 Measurement storage in memory Optional Remote Probe accessory > 6610: Phase Rotation Meter: The Phase Rotation Meter Model 6610 is an essential tool for any installation, inspection and maintenance facility. The Model 6610 is a phase meter with voltage sensing detector clips (no metal contact points) designed to identify phase rotation on 3-phase systems and identify live and open/de-energized phases. The phase order is determined as soon as the leads are connected. The presence of live wires and phase sequence are provided by LED indication and buzzer as soon as detection has occurred. The Model 6610 is ideal for installing rotating machinery or motors, and for checking generator phase rotation direction. 205: Power Clamp-on Meter, 1000VAC/DC: The True RMS Clamp-On Meter Model 205 is safety rated at 600V CAT IV. It measures AC DC volts and amps, frequency, continuity, resistance, power and Power Factor, phase rotation, and THD. It can also perform diode checks. The Delta relative function compares new measurements to a reference value, and the MIN/MAX function tracks high and low values. The Model 205 also tracks peak and peak- values. This compact and rugged meter can operate in the most demanding work environments, and its IP40 rating allows it to withstand both dust and water spray. Large Tool Bag: Dimensions: 18 x 9 x 12

Quality Control: Test New Motors or Stored Spares Trouble Shooting: Test Suspect Motors and know Immediately if the Problem is Electrical or Mechanical, Stator or Rotor Related Trending: Early Warning of any Change in the Motor’s Electrical Condition, Stator and Rotor > Each Unit Includes Software Three Test Leads with KELVIN Type Clips One Test Lead for Ground Test One Battery Charger 85-260 VAC One Hard Carrying Case.

Detects all of the following: Turn-to-Turn Faults Coil-to-Coil and Phase-to-Phase Faults Open Phases Phase Unbalances Broken Rotor Bars Grounded Windings Capacitor Failures (Pass/Fail Test) Shorted Armature Windings (DC Motors) Works on All Sizes of Motors—Fractional Through Thousands of HP Low-Voltage Tests are Non-Destructive > Each Unit Includes Soft Carrying Pouch Test Leads User CD with Step-by-Step Operating Instructions

The perfect tool for trouble shooting, start-up, and quality control of low voltage AC induction motors. Know in a few minutes what the problem is: connections or cable, electrical or mechanical, coil, internal fault or ground fault Make sure electrical motors, connections and cables are working in top condition Test new and stored spare motors. Test repaired motors to end irregularities or a possible faulty repair with different wire sizes, or wiring configuration Safe: De-energized testing Easy: As easy to use as any Meg-ohm-meter or multimeter Light: 1 pound, hand-held Batteries: They last for up to 10 hours of testing Best Value: Costs less than a good Meg-Ohm-Meter ordering a quick return on your investment

Quality Control: Test New Motors or Stored Spares Trouble Shooting: Test Suspect Motors and know Immediately if the Problem is Electrical or Mechanical, Stator or Rotor Related Trending: Early Warning of any Change in the Motor’s Electrical Condition, Stator and Rotor PC software NOT included > Each Unit Includes Three Test Leads with KELVIN Type Clips One Test Lead for Ground Test One Battery Charger 85-260 VAC One Hard Carrying Case.

Professionals who install or maintain 3-phase motors or systems recognize the importance of verifying the correct motor rotation and wiring phase sequence. Improper connections can cause motors to rotate in reverse direction, potentially damaging the motor and the equipment it is powering. The PRM-6 Phase Sequence and Motor Rotation Tester can safely, easily, and reliably test the motor rotation of 3-phase systems with traditional test leads. In addition, it can verify 3-phase receptacle wiring and phase sequencing. Durably constructed with a rubber outer casing, the PRM-6 has a bright, backlight LCD display, CAT IV 600 V rating, and conforms to EN 61010 and EN 61557 standards, making it an essential tool for motor rotation and phase sequence testing in commercial and industrial environments on electrical systems up to 700 V. 3-phase wire sequence indication Synchronous or asynchronous motor rotation direction Error displays (missing phase, one input connected to neutral or PE) Non-contact, wireless motor rotation detection on running motors Indicates motor rotation of disconnected motors when spinning the shaft by hand or other means 3-phase to phase voltage up to 700 V Clear LCD, backlight display with easy to read symbols Durable, rubber casing for 3 ft. (1 m) drop-proof protection Low battery warning Safety: CAT IV 600V

6 ranges with 3 sub-ranges in each current range Measurement of resistive and inductive materials 5-Digit backlit LCD, PC interface Auto or Manual ranging, 10A maximum test current Store/Recall up to 3000 measurements Cable length measurement (feet or meters) > Each Unit Includes 4-wire cables with Kelvin clip connectors Rechargeable Li-Polymer battery AC adapter/charger Software and USB cable Soft carrying case

The Fluke 9040 is effective for measuring phase rotation in all areas where three phase supplies are used to feed motors, drives and electrical systems. The Fluke 9040 is a rotary field indicator and can provide clear indication of the 3 phase via an LCD display and the phase rotation direction to determine correct connections. It allows rapid determination of phase sequence and has a voltage (up to 700 V) and frequency range suitable for commercial and industrial applications. The included test probes have a variable clamping range for safe contact, also in industrial sockets. Phase rotation indicator with high voltage capability for industrial applications The Fluke 9040 is a rotary field indicator and can provide clear indication of the 3 phase via an LCD display and the phase rotation direction to determine correct connections 3 phase indication Indication of phase rotation Clear LCD display No battery required > Each Unit Includes 3 self-retaining test probes (black) Alligator clip User manual