Megohmmeters and Insulation Testers

The integral Li-on battery supplies a constant 100A current for up to 30 minutes or up to 360 Manual/Auto tests to enable enhanced productivity in remote locations. With a focus on user safety, advanced design features ensure the safe operation of the instrument in the most adverse conditions, including a CATIV 600V safety rating in accordance with IEC61010. The rugged design, intuitive interface and IP54 (lid open) rating ensure reliability and ease of use in the most arduous of conditions. FREE transit case!!! (Over a $490 value) Display clearly showing large digits for test results and visible in all light conditions Single button to save test results and to automatically save in auto mode IP54 for protection against dust and rain during testing Clearly visible C and P LEDs showing continiuity or current and potential connections Smooth DC Output on C1 and C2 terminals High noise immunity on P1 and P2 terminals CAT IV 600 VAC/500 VDC safety rating on all Terminal DualGround capability with the DC clamp Quick and easy rotary switch selection of 10A, 50A, 100A tests no configuration required Rotary switch selection of view, download and delete test results Simple navigation of setup and stored results Rotary switch selection of test modes and off position USB for communications Backlight for low light conditions

High current loop tester Single and 3 phase testing 16 Hz to 400 Hz operation CATIV 300 V applications Two wire lead set or mains plug leads Tough armoured case Built-in cover > Each Unit Includes Two wire lead set or mains plug leads

The MFT70 Multifunction Tester is designed for testing low voltage electrical installations to fulfill the requirements of NFPA70 and the National Electrical Code. It provides all the tests required to complete the necessary electrical certification for industrial, commercial and domestic fixed wiring installations, including: System voltage and frequency measurement (TRMS) Insulation test at 100 V, 250 V, 500 V and 1000 V Input protection against live circuits up to 600 V even when insulation test is locked-on Continuity resistance at 200 mA or 15 mA Automatic – no need to press TEST which leaves both hands free to hold probes Resistance range up to 100 kΩ Fast continuity buzzer and selectable thresholds GFCI test Ramp test displays trip current Ground testing 2-pole 3-pole Attached Rod Technique (ART) Stakeless techniques > More Features: Simple color-coded test selection and largeclear backlit display for ease of use Internal memory and Bluetooth®communications 3-terminal ground test and stake less testing for spike resistance measurement GFCI testing as defined in the ANSI/UL 943, CSA C22.2 No. 144.1 and ANCE NMX-J-520 IEC61010 CATIV safety ratings and toughIP54 case

These instruments are designed based on Meggers extensive knowledge of insulation testing (100 years of experience) and significant feedback from actual end users. Megger has taken the best insulation testers in the world and improved them to add functionality, make them easier to use and easier to transport. They include Meggers patented digital/analog display (real-time pointer movement), a CATIV safety rating at all terminals and a unique dual case design. Smaller size and lighter weight allows easier transport and use without compromising performance. High measurement range enables installation testing and long-term trending of higher value apparatus. Unique dual case design allows for fire-retardant protection while maintaining ruggedness. High-quality, flexible silicon test leads meet safety regulations of IEC 61010-31:2008 while ensuring measurement accuracy. Timed IR plus PI, DAR, DD, SV and ramp tests maximize diagnostic testing capability. Operate from line power when battery fully discharged (charges while operating). Two and one-half hour full battery charge time (one half hour charge for one hour testing) significantly increases productivity. Up to six hours continuous testing (5 kV) on a single battery charge. Industry best guard terminal performance to insure highest accuracy of measured values. Enhanced driver technology provides plug-and-play when connected to the internet. No tedious and potentially interruptive setup procedures. Dedicated voltmeter function (30 V to 660 V) with frequency measurement allows the user to check for induced voltages. CATIV 600 V safety rating on all terminals allows for safe use in the widest range of applications. Large LCD with automatic backlight. Noise filter rejects up to 3 mA noise for effective operation in electrically noisy environments. High altitude operation up to 3000 m while maintaining CATIV 600 V rating. Rotary switch operation for easy, intuitive field use. Field replaceable battery > Each Unit Includes User guide CD Power lead 10 ft (3 m) leadset x 3, medium insulated clips 10 ft (3 m) 3 m leadset x 3, large insulated clips

Save over $490 with this VIP Kit! (FREE transit case included) Smaller size and lighter weight allows easier transport and use without compromising performance. High measurement range enables installation testing and long-term trending of higher value apparatus. Unique dual case design allows for fire-retardant protection while maintaining ruggedness. High-quality, flexible silicon test leads meet safety regulations of IEC 61010-31:2008 while ensuring measurement accuracy. Timed IR plus PI, DAR, DD, SV and ramp tests maximize diagnostic testing capability. Operate from line power when battery fully discharged (charges while operating). Two and one-half hour full battery charge time (one half hour charge for one hour testing) significantly increases productivity. Up to six hours continuous testing (5 kV) on a single battery charge. Industry best guard terminal performance to insure highest accuracy of measured values. Enhanced driver technology provides plug-and-play when connected to the internet. No tedious and potentially interruptive setup procedures. Dedicated voltmeter function (30 V to 660 V) with frequency measurement allows the user to check for induced voltages. CATIV 600 V safety rating on all terminals allows for safe use in the widest range of applications. Large LCD with automatic backlight. Noise filter rejects up to 3 mA noise for effective operation in electrically noisy environments. High altitude operation up to 3000 m while maintaining CATIV 600 V rating. Rotary switch operation for easy, intuitive field use. Field replaceable battery > Each Unit Includes FREE transit case (Over a $490 value!!!!) User guide CD Power lead 10 ft (3 m) leadset x 3, medium insulated clips 10 ft (3 m) 3 m leadset x 3, large insulated clips

Offering CAT IV, the Megger MIT1025 10-kV Insulation Resistance Tester is compact, light 10 kV insulation resistance tester for the diagnostic testing and maintenance of high voltage electrical equipment. Enclosed in a tough case it is both smaller and lighter than its predecessor making it even easier to carry and store. Save over $735 with the Megger MIT1025 VIP Kit Limited Time Offer FREE Megger MIT410/2 Smaller size and lighter weight allows easier transport and use without compromising performance. High measurement range enables installation testing and long-term trending of higher value apparatus. Unique dual case design allows for fire-retardant protection while maintaining ruggedness. High-quality, flexible silicon test leads meet safety regulations of IEC 61010-31:2008 while ensuring measurement accuracy. Timed IR plus PI, DAR, DD, SV and ramp tests maximize diagnostic testing capability. Operate from line power when battery fully discharged (charges while operating). Two and one-half hour full battery charge time (one half hour charge for one hour testing) significantly increases productivity. Up to six hours continuous testing (5 kV) on a single battery charge. Industry best guard terminal performance to insure highest accuracy of measured values. Enhanced driver technology provides plug-and-play when connected to the internet. No tedious and potentially interruptive setup procedures. Dedicated voltmeter function (30 V to 660 V) with frequency measurement allows the user to check for induced voltages. CATIV 600 V safety rating on all terminals allows for safe use in the widest range of applications. Large LCD with automatic backlight. Noise filter rejects up to 3 mA noise for effective operation in electrically noisy environments. High altitude operation up to 3000 m while maintaining CATIV 600 V rating. Rotary switch operation for easy, intuitive field use. Field replaceable battery > Each Unit Includes FREE MIT410/2 User guide CD Power lead 10 ft (3 m) leadset x 3, medium insulated clips 10 ft (3 m) 3 m leadset x 3, large insulated clips

Save over $490 with this VIP Kit! (FREE transit case included) Insulation resistance up to 30 TO @ 15 kV, 20 TO @ 10kV, 10 TO @ 5 kV IR, Timed IR, DAR, PI, DD, SV and ramp diagnostic tests High current 3 mA short circuit current High noise immunity 3mA (5kV and 10kV) 6mA (15kV) of noise rejection Li-ion battery up to 6 hrs continuous testing @ 5 kV with a 100M load, battery meets IEC 62133 Safety rating: CATIV 600 V to 3000 m (5 kV, 10 kV) CATIV 1000 V to 3000 m (15 kV) Large LCD display with backlight Dedicated voltmeter function (30 V to 660 V) Advanced memory, on screen recall and real time clock for date/time stamped results Download of on-board results via USB interface PowerDB Lite asset management software Recorded temperature (measured by independent instruments) can be saved with test result PowerDB Lite asset management software supplied > Each Unit Includes FREE transit case (Over a $490 value!!!) Power lead USB cable PowerDB Lite software Product Information CD

The Megger MIT200 series digital/analog handheld insulation resistance tester measures insulation resistance, voltage, and continuity in electrical installations, building maintenance, and electrical testing. The average-sensing meter provides accurate readings when measuring linear loads, where the current or voltage has a sinusoidal waveform. The dual LCD screen indicates test results either digitally or with an analog arc function to replicate the response of analog meters. Insulation testing to 1000 MW Continuity testing at 200 mA down to 0.01W Live Circuit Warning (voltage display) and Test Inhibit Digital/Analog Display Alkaline or Rechargeable Batteries –10ºC to 55ºC Operating Temperature CATIII 600 V Conforms to EN61557-1, IEC 61010-1 3 Year Warranty Calibration Certificate > Each Unit Includes Lead set with prods and clips Carrying Case