Flowmeters

Designed for Water Applications Schedule 80 PVC Specifi cations Standard with Rate and Two Total Low-Profile Display Female NPT Connections

Designed for Water Applications Schedule 80 PVC Specifications Standard with Rate and Two Total Low-Profile Display Female NPT Connections

Design Type Turbine Fitting Size 3/4 Inch Fitting Type NPT (Female) Housing Material PVC Flow Range 2 to 20 GPM 7.6 to 76 LPM Accuracy (% of Reading Turbine with Computer) ±3.0 % Operating Temperature Range 32 to 140 ºF 0 to 60 ºC Reads Gallons Litres Pressure Rating at 73ºF 225 psi 15.3 bar Battery Life 5 Years Typical K-Factor 1100 Electronic Choice 09 2 Totals (1 Resettable/ 1 Cumulative), Factory Calibration in Gallons and Litres, 2 User Calibrations and Flowrate Wetted Material Housing PVC Wetted Material Bearings Ceramic Wetted Material Shaft Tungsten Carbide Wetted Material Rotor PVDF Wetted Material Rings 316 Stainless Steel

Inline for ease of installation and low cost Gas, liquid, and steam applications Line size 1 1/2 1/4 Probe Diameter Steel Rating: 250 PSIG @ 250°F Max

Inline for ease of installation and low cost Gas, liquid, and steam applications Line size 1 1/2 1/4 Probe Diameter Steel Rating: 250 PSIG @ 250°F Max

The FDT-30 Series provides easy and low cost installation by clamping to the outside of existing piping systems. Non-invasive transit time system allows solids to pass through the pipe with no affect on the meter. Y-strainers or filtering devices are not needed. Greater accuracy can be attained in applications consisting of entrained gases. 2 to 100 LPM (0.5 to 25 GPM) range, 1/2 plastic tubing Compact Enclosure Large Digital Display 4 to 20 mA, TTL and Turbine Simulated Outputs Rate and Total Displays Clean Liquid Compatible Liquid Types: Most clean liquids, or liquids containing moderate amounts of suspended solids Power: 11.4 to 30 Vdc @ 0.25 A Velocity: 0.03 to 12.4 MPS (0.1 to 40 FPS) 4 to 20 mA Output (Standard): 12-bit resolution, source power, 5V max insertion loss, 900 Ω max loop impedance, can share ground common with power supply-isolated from piping system Turbine Frequency Output (TTL Pulse): Switch selectable, non-ground referenced AC, ground referenced squarewave, 100 mV pp min/5 Vdc amplitude, 0 to 1 kHz range, 50% ±10% duty cycle Display: 2 line x 8 character LCD alternates between rate and total in 10 second intervals Top Row: 18 mm (0.7), 7-segment Bottom Row: 9 mm (0.35), 14-segment Rate: 8 digits max Totalizer: 8 digits max, exponential multipliers from -1 to 6 Units: Feet, gallons, ft³, million-gal, barrels (liquid and oil), acre-feet, lbs, meters, m³, liters, million-liters, kg, rates programmable for per: sec, min, hr, or day Operating Ambient: -40 to 85°C (-40 to 185°F) Enclosure: NEMA 3 ABS, PVC and Ultem, brass or SS hardware Dimensions: 75 W x 150 L x 63 mm D (3 x 6 x 2.5) Transducer Type: Clamp-on for pipe mount, time of flight ultrasonic Accuracy: ±1% rdg @ rates &gt, 0.3 MPS (1 FPS), ±0.003 MPS (0.01 FPS) @ rates &lt, 0.3 MPS (1 FPS) Repeatability: ±0.5% rdg Response Time: 0.3 to 30 sec, adjustable Protection: Reverse polarity, surge suppression Pipe Sizes: 12 to 50 mm (0.5 to 2) Pipe Materials: Carbon steel, stainless steel, copper and plastic

Massflow 0-10 SLM ±1% Accuracy Linear Output Low Cost Thermal Technology For Flow Rates up to 75 SLM Power Supply Included Comes standard with 5-point NIST cert Accuracy: ±1% of full scale including linearity Repeatability: ±0.15% full scale or better Turndown Ratio: 100:1 Response Time: 5 seconds Gas Ambient Temperature: 0 to 50°C (32 to 122°F) Temperature Coefficient: 0.05% full scale per 1°C or better Pressure Coefficient: 0.01% full scale per psi or better Minimum Pressure Requirements: Meters: 1 inch of H2O Controllers ≤1 SLM: 1 psi Controllers &gt,20 SLM: 20 psi Differential Pressure for Mass Flow Controllers:5 LPM: 20 to 40 psi standard Maximum Gas Pressure: Polyacetal: 250 psig 316 SS: 500 psig Leak Integrity: 1 x10-6 cc/min of He or better Wetted Parts: Standard: Polyacetal, FKM O-rings Optional: 316 SS, FKM O-rings Connections: 1/4 FNPT standard, 1/4 compression fitting for all stainless steel models Input/Output Connection: 9-pin sub-D connector Control Signal: 0 to 5 Vdc Control Valve: Electromagnetic normally closed Output signal: Linear 0 to 5 Vdc, 1000 Ω min load, 4 to 20 mA, 500 Ω loop resistance Input Power: Meters: 24 Vdc @ 150 mA, 115 Vac, 220 Vac with AC adaptor Controller: 24 Vdc @ 300 mA, 115 Vac, 220 Vac with AC adaptor Weight: 1.25 kg (2.75 lb) with power supply

Polyacetal Mass Flowmeter With Display 0 to 15 SLM ±1% Accuracy Linear Output Low Cost Thermal Technology For Flow Rates up to 75 SLM Power Supply Included Comes standard with 5-point NIST cert Accuracy: ±1% of full scale including linearity Repeatability: ±0.15% full scale or better Turndown Ratio: 100:1 Response Time: 5 seconds Gas Ambient Temperature: 0 to 50°C (32 to 122°F) Temperature Coefficient: 0.05% full scale per 1°C or better Pressure Coefficient: 0.01% full scale per psi or better Minimum Pressure Requirements: Meters: 1 inch of H2O Controllers ≤1 SLM: 1 psi Controllers &gt,20 SLM: 20 psi Differential Pressure for Mass Flow Controllers:5 LPM: 20 to 40 psi standard Maximum Gas Pressure: Polyacetal: 250 psig 316 SS: 500 psig Leak Integrity: 1 x10-6 cc/min of He or better Wetted Parts: Standard: Polyacetal, FKM O-rings Optional: 316 SS, FKM O-rings Connections: 1/4 FNPT standard, 1/4 compression fitting for all stainless steel models Input/Output Connection: 9-pin sub-D connector Control Signal: 0 to 5 Vdc Control Valve: Electromagnetic normally closed Output signal: Linear 0 to 5 Vdc, 1000 Ω min load, 4 to 20 mA, 500 Ω loop resistance Input Power: Meters: 24 Vdc @ 150 mA, 115 Vac, 220 Vac with AC adaptor Controller: 24 Vdc @ 300 mA, 115 Vac, 220 Vac with AC adaptor Weight: 1.25 kg (2.75 lb) with power supply