Showing 1–9 of 26 results
Quality Control: Test New Motors or Stored Spares Trouble Shooting: Test Suspect Motors and know Immediately if the Problem is Electrical or Mechanical, Stator or Rotor Related Trending: Early Warning of any Change in the Motor’s Electrical Condition, Stator and Rotor > Each Unit Includes Software Three Test Leads with KELVIN Type Clips One Test Lead for Ground Test One Battery Charger 85-260 VAC One Hard Carrying Case.
Detects all of the following: Turn-to-Turn Faults Coil-to-Coil and Phase-to-Phase Faults Open Phases Phase Unbalances Broken Rotor Bars Grounded Windings Capacitor Failures (Pass/Fail Test) Shorted Armature Windings (DC Motors) Works on All Sizes of Motors—Fractional Through Thousands of HP Low-Voltage Tests are Non-Destructive > Each Unit Includes Soft Carrying Pouch Test Leads User CD with Step-by-Step Operating Instructions
The perfect tool for trouble shooting, start-up, and quality control of low voltage AC induction motors. Know in a few minutes what the problem is: connections or cable, electrical or mechanical, coil, internal fault or ground fault Make sure electrical motors, connections and cables are working in top condition Test new and stored spare motors. Test repaired motors to end irregularities or a possible faulty repair with different wire sizes, or wiring configuration Safe: De-energized testing Easy: As easy to use as any Meg-ohm-meter or multimeter Light: 1 pound, hand-held Batteries: They last for up to 10 hours of testing Best Value: Costs less than a good Meg-Ohm-Meter ordering a quick return on your investment
Quality Control: Test New Motors or Stored Spares Trouble Shooting: Test Suspect Motors and know Immediately if the Problem is Electrical or Mechanical, Stator or Rotor Related Trending: Early Warning of any Change in the Motor’s Electrical Condition, Stator and Rotor PC software NOT included > Each Unit Includes Three Test Leads with KELVIN Type Clips One Test Lead for Ground Test One Battery Charger 85-260 VAC One Hard Carrying Case.
JM Test Model # PCS-01 Pressure Resolution Control in Tenths in PSI and Hundredths in Inches of Water Precise Regulator for Generating an Approximate Pressure Setting Precise Volume Adjust for “Fine Tuning” the Pressure Setting Front Panel Vent for Venting the Pressure to Atmosphere (2) Two Test Ports : One Port to Attach to Any Pressure Standard/Calibrator, the Other to Attach to the Device Under Test (DUT)
Use with Any Pressure Calibrator for High and Low Pressures Pressure Cylinder for Storage of 2200 PSI Easily Refillable with Standard Nitrogen or Compressed Air Bottle/Systems Precision Volume Controller Attached to the Output of the Regulator for “Fine Tuning” the Pressure Two Test Ports on the Front Control Panel Durable Rugged Case (polyethylene)
Dual Cylinder Use with Any Pressure Calibrator for High and Low Pressures Pressure Cylinder for Storage of 2200 PSI Easily Refillable with Standard Nitrogen or Compressed Air Bottle/Systems Precision Volume Controller Attached to the Output of the Regulator for “Fine Tuning” the Pressure Two Test Ports on the Front Control Panel Durable Rugged Case (polyethylene)
Look before you dig! The LKZ-1000 allows construction crews to: Detect underground energized (live) wires Detect de-energized underground wires Trace metallic or non-conductive pipes Trace a determined cable Determine the depth of a cable > The LKZ-1000 cable & pipe locator consists of an improved LKN-1000 transmitter and the LKO-1000 receiver that together deliver significantly higher detection technology to: Detect underground services at greater depths Give more accurate depth estimation Detect in the presence of high signal interference > LKZ-1000 Technology: Four adjustable output levels with maximum output level of 1 W Choice of 3 tracing signals, 8 kHz or 33 kHz, or at 8 kHz and 33 kHz together Locates cables up to 3 m, 10 ft deep Trace non-conductive pipelines using a “floating” probe Transmitter detection of de-energized underground wires using a galvanized, inductive, or clamp-based connection Trace metallic or non-conductive pipes using an additional probe Location by connecting the transmitter directly to an object that is not live Location by using an adapter that connects the transmitter to an AC outlet > User-friendly Design Features: Compact and light-weight for less fatigue when operating for long periods Sensibly located control buttons for hand operation Easy-to-view backlit LCD with contrast auto on-off Clear visual and audio signals for easier operation Automatic adjustment of detection sensitivity 5 operating modes Durable waterproof design for harsh outdoor conditions, protection rating of IP65 Self-test function to test the LKN-1000 before use Shallow cable-depth warning indicator Cable direction indication Audio tones to facilitate locating or tracing Adjustment of transmitter power and frequency > Passive or Active Operating Modes: Passive POWER with 50 Hz or 60 Hz – enables location of live wires and cables Passive RADIO (15-30 kHz) – for quick, non-selective location of an underground metallic installation Active with transmitter (8 kHz and 33 kHz), enables detection using the inductive mode, just place the transmitter over the traced object
The LKZ-720 is a professional-grade tool for locating cables, wires, and conduits. It is an essential tool for electrical technicians, contractors, and maintenance engineers. Detect cables in ceilings, walls and floors Detect breaks in cables Trace cables in building installations Locate power sources and switches Locate short-circuits between wires Trace shielded cables Trace cables in metal ducts Identify fuses and breakers on panels and distribution boards Trace underground cables Tracing conductive water and heating pipes Detect of live cables by non-contact Detect the direction of current flow Accurate locating the source Phase detection mode Receiver operates with four transmitters to locate interruptions or distinguish wires Bright LED flashlight Headphone jack in receiver Backlit display Battery status User-configured settings of transmitter to receiver Operation on systems up to 500V RMS Measurement of voltage to 500 Vrms 3 levels of transmitter amplification Automatic or manual selection of transmitter operation 5 modes of wire tracer operation voltage, current, current-voltage, power and current lamp Software upgrade via USB Additional accessories enable precise localization with contact or non-contact probes, and current clamp
No products in the cart.
