Showing 1–9 of 19 results

  • Sonel Test Measurement LKZ-1000

    $1.312

    Look before you dig! The LKZ-1000 allows construction crews to: Detect underground energized (live) wires Detect de-energized underground wires Trace metallic or non-conductive pipes Trace a determined cable Determine the depth of a cable > The LKZ-1000 cable & pipe locator consists of an improved LKN-1000 transmitter and the LKO-1000 receiver that together deliver significantly higher detection technology to: Detect underground services at greater depths Give more accurate depth estimation Detect in the presence of high signal interference > LKZ-1000 Technology: Four adjustable output levels with maximum output level of 1 W Choice of 3 tracing signals, 8 kHz or 33 kHz, or at 8 kHz and 33 kHz together Locates cables up to 3 m, 10 ft deep Trace non-conductive pipelines using a “floating” probe Transmitter detection of de-energized underground wires using a galvanized, inductive, or clamp-based connection Trace metallic or non-conductive pipes using an additional probe Location by connecting the transmitter directly to an object that is not live Location by using an adapter that connects the transmitter to an AC outlet > User-friendly Design Features: Compact and light-weight for less fatigue when operating for long periods Sensibly located control buttons for hand operation Easy-to-view backlit LCD with contrast auto on-off Clear visual and audio signals for easier operation Automatic adjustment of detection sensitivity 5 operating modes Durable waterproof design for harsh outdoor conditions, protection rating of IP65 Self-test function to test the LKN-1000 before use Shallow cable-depth warning indicator Cable direction indication Audio tones to facilitate locating or tracing Adjustment of transmitter power and frequency > Passive or Active Operating Modes: Passive POWER with 50 Hz or 60 Hz – enables location of live wires and cables Passive RADIO (15-30 kHz) – for quick, non-selective location of an underground metallic installation Active with transmitter (8 kHz and 33 kHz), enables detection using the inductive mode, just place the transmitter over the traced object

  • Sonel Test Measurement LKZ-720

    $662

    The LKZ-720 is a professional-grade tool for locating cables, wires, and conduits. It is an essential tool for electrical technicians, contractors, and maintenance engineers. Detect cables in ceilings, walls and floors Detect breaks in cables Trace cables in building installations Locate power sources and switches Locate short-circuits between wires Trace shielded cables Trace cables in metal ducts Identify fuses and breakers on panels and distribution boards Trace underground cables Tracing conductive water and heating pipes Detect of live cables by non-contact Detect the direction of current flow Accurate locating the source Phase detection mode Receiver operates with four transmitters to locate interruptions or distinguish wires Bright LED flashlight Headphone jack in receiver Backlit display Battery status User-configured settings of transmitter to receiver Operation on systems up to 500V RMS Measurement of voltage to 500 Vrms 3 levels of transmitter amplification Automatic or manual selection of transmitter operation 5 modes of wire tracer operation voltage, current, current-voltage, power and current lamp Software upgrade via USB Additional accessories enable precise localization with contact or non-contact probes, and current clamp

  • Sonel Test Measurement LXP-10A

    $513
  • Sonel Test Measurement MIC-05S1

    $1.740

    The MIC-05s1 is a portable, rugged, easy-to-use, 5 kV class insulation test meter. Measurement to 20 TΩ User-selectable test voltage any from 50 to 1,000 V (with 10 V resolution) and 1,000 to 5,000 V (with 25 V resolution) Continuous indication of measured insulation resistance or leakage current Audio beeps every five-second periods to indicate measurement progress Indication of actual test voltage during measurement 1.2 mA, 3 mA and 5 mA test current Step voltage and ramp voltage insulation resistance measurements (SV) (RV) Selectable test times (T1, T2 , T3 from 1 to 600 seconds) to measure one or two absorption coefficients Adjustable measuring time to 99 59’ Polarization index (PI) and dielectric absorption ratio (DAR) measurements Dielectric Discharge calculation (DD) High-noise immunity, digital filters function for measurements in high noise environment (10 s, 30 s , 60 s) Adjustable limits for measured resistance RISO Measurement of capacitance during the measurement of RISO DC and AC voltage measurement in the range of 0 to 600 V Meter conforms to EN 61557 > Safety First Features: CAT-IV 600V, CAT-III 1000V Automatic discharge of tested object after the insulation resistance measurement completes to remove high voltage charge remaining due to cable capacitance Protection against measuring live objects, measurement will not proceed Measurements with test leads up to 65 ft / 20 m length > Construction: Backlit keyboard and graphical display Rugged IP 54 case protected from water spray from any direction > Power Supply: Bult-in battery pack, low battery warning indicator, built-in fast charger AC power: 90 V to 260 V, 50 Hz / 60 HzGraphical display > Memory: 990 cells of memory (11,880 records) to save test results Wireless data transmission to a PC with Bluetooth®, or via USB cable

  • Sonel Test Measurement MIC-10

    $267

    The MIC-10 is a hand-held, rugged, easy-to-use, 1 kV class insulation test meter. The MIC-10 has a wide measurement range, selectable test voltages, and excellent safety features. Insulation resistance measurement to 10 GΩ User selected test voltages: 50, 100, 250, 500, 1000 V Displays continuous indication of insulation resistance Audio beeps every five-second periods to indicate measurement progress Indication of actual test voltage during the measurement Three-lead measurement Continuity measurement of protective and equipotential conductors according to EN 61557-4 Low-voltage circuit continuity and resistance measurement Circuit resistance measurement (&lt,1999 Ω) Audio alert signal if circuit resistance is below 30 Ω Capacitance measurement during the RISO measurement Measurement of alternating and direct voltages from 0 to 600 V Meter conforms to EN 61557 Automatic discharge of tested object after the insulation resistance measurement completes to remove high voltage charge remaining due to cable capacitance Protection against measuring live objects, measurement will not proceed Power Supply 4 AA disposable or rechargeable batteries Indicates state of battery charge

  • Sonel Test Measurement MIC-10S1

    $2.415

    The MIC-10s1 is a portable, rugged, easy-to-use, 10kV class insulation test meter. The MIC-10s1 has a wide measurement range, selectable test voltages, and excellent safety features. Insulation resistance to 40.0 TΩ User-selectable test voltage any from 50 V to 1,000 V (with 10 V resolution) and 1,000 V to 10,000 V (with 25 V resolution) Continuous indication of measured insulation resistance or leakage current Audio beeps every five-second periods to indicate measurement progress Indication of actual test voltage during measurement 1.2 mA, 3 mA and 5 mA test current Step voltage and ramp voltage insulation resistance measurements (SV) (RV) Selectable test times (T1, T2 , T3 from 1 to 600 seconds) to measure one or two absorption coefficients Adjustable measuring time to 99 59’ Polarization index (PI) and dielectric absorption ratio (DAR) measurements Dielectric Discharge calculation (DD) Digital filters function for measurements in high-noise environment (10 s, 30 s , 60 s) High-noise immunity, up to 1550 V (induced) Adjustable limit settings for measured resistance RISO Measurement of capacitance during the measurement of RISO DC and AC voltage measurement in the range of 0 V to 600 V Graphical display of R and V, or R and I, plots the progress of test in real-time, and final graph (see example below) Meter conforms to EN 61557 > Safety First: CAT-IV 600V, CAT-III 1000V Automatic discharge of tested object after measurement completes to remove high voltage charges remaining on cable Protection against measuring live objects, measurement will not proceed Measurements with test leads up to 180 ft / 55 m length > Construction: Backlit keyboard and graphical display Rugged IP 54 case protected from water spray from any direction > Power Supply: Built-in battery pack, low battery warning indicator, built-in fast charger AC power: 90 V to 260 V, 50 Hz / 60 Hz > Memory: 990 cells of memory (11,880 records) to save test results Wireless data transmission to a PC with Bluetooth®, or via USB cable

  • Sonel Test Measurement MIC-2501

    $812

    Indicating the conditions of the insulation of electrical networks and equipment is an important element for ensuring efficient protection against electric shocks. Recently, the company, SONEL S.A., has been working hard on the development and production of state-of-the art devices for such testing. A number of models with test voltages up to 5 kV and to 10 kV have been implemented. Due to extended measurement functions and immunity to electric fields and other interferences, they are one of the leading products used in professional power engineering for complex and advanced insulation resistance testing. Common insulation resistance tests carried out in receiving end of the electrical grids do not require such extended measurement functions, as this leads to an increase in the overall dimensions of the device. Therefore, with a large group of electricians in mind who test receiving end electrical systems in the broadly defined municipal infrastructure, industries, office buildings or private housing – Sonel MIC-2501, a new insulation resistance tester has been designed and launched onto the market. This kind of testing is most often carried out by small or even one-man electrical service companies. Therefore, the main objective was to design such a device where the high technical parameters would be maintained, while its manufacturing costs would be optimized and reduced compared to those of previous models. It should be emphasized that both the functionality and ergonomics result from collaboration with the present users of meters manufactured by Sonel S.A. The device has been designed in compliance with PN-EN 61557- 2 and allows insulation resistance testing to be performed as described in, amongst others, PN-HD 60364-6 and PN-EN 04700. Two- or three-lead insulation resistance measurement Selectable measurement voltage from the range 100 to 2500 V in100 V steps Acoustic determination of five-second periods of time Measuring T1, T2 and T3 times to determine absorption coefficients for 15, 60 and 600 s, indication of actual test voltage during measurement, protection against measuring live objects Low voltage measurement of circuit continuity and resistance: leakage current measurement during insulation resistance testing DC and AC voltage measurement within the range 0750 V Memory: 990 cells (11880 records), data transmission to the PC through the USB cable Battery-powered insulation tester

  • Sonel Test Measurement MIC-30

    $389

    The MIC-30 is a hand-held, rugged, easy-to-use, 1 kV class insulation test meter. The MIC-30 has a wide measurement range, selectable test voltages, and excellent safety features. Insulation resistance measurement to 100 GΩ User selected test voltages: 50, 100, 250, 500, 1000 V in 10 V steps Displays continuous indication of insulation resistance or leakage current Audio beeps every five-second periods to indicate measurement progress Indication of actual test voltage during the measurement Three-lead measurement Continuity measurement of protective and equipotential conductors according to EN 61557-4 Low-voltage circuit continuity and resistance measurement: Circuit resistance measurement (&lt,1999 Ω) Audio alert signal if circuit resistance is below 30 Ω Capacitance measurement during measurement Measurement of alternating and direct voltages from 0 to 600 V Automatic measurement in sockets with the UNI-Schuko adapter with possibility of configuring pairs of measured cable Selectable test times (T1, T2 , T3 from 1 to 600 seconds) to measure one or two absorption coefficients Meter conforms to EN 61557 Automatic discharge of tested object after the insulation resistance measurement completes to remove high voltage charge remaining due to cable capacitance Protection against measuring live objects, measurement will not proceed Power Supply 4 AA disposable or rechargeable batteries Continuous indication of state of battery charge 990 memory cells to save test results Wireless data transmission to computer using the Bluetooth

  • Sonel Test Measurement MIC-5001

    $970

    Insulation resistance measurement in a compact, light-weight, low-cost design. Measurement to 5 TΩ Measuring voltage selectable from 50 V to 500 V range in 50 V steps, and from 500 V to 5000 V range in 100 V steps Continuous indication of insulation resistance or leakage current Automatic discharge of stored charge due to capacitance of tested object after the insulation resistance measurement Audio beeps every five seconds to alert user test is proceeding, and to get time characteristics Measured test times of T1, T2 and T3 for measuring Absorption Coefficient, Dielectric Absorption Ratio DAR. and Polarization Index PI Continuous display of test voltage during the measurement Protection against measuring live objects Two and three-lead measurement method Ramp Test Insulation resistance measurement Measurement of breakdown voltage with increments up to 1 kV / s Measurement of alternating and direct voltages from 0 V to 750 V 990 cells of memory (11880 records) to record results Data transfer to PC via USB cable Built-in rechargeable battery pack Meets the requirements of the EN 61557 standard Charge from optional car lighter (12 V) socket accessory